Almost everyone maintains his or her own conception about How to Install a Bathtub.
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also often, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently accessible, the job can relocate rapidly; if you have to open a wall surface to remove the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly aid you install a new bathtub in your restroom if you have actually currently gotten a new tub and also do not require to alter the arrangement of your previous water supply pipes.
Your devices as well as material checklist must make up the following:
Preparing for the Installment
To start with, the supporting frame provided with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly come from the pipelines. Once the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used at least once as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet as well as the sink. Protect the tap in place with the producer provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The previous type should be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, creating the water to permeate the wall between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been brought to that write-up on How to Install a Bathtub through a friend on another site. Don't hesitate to set aside a second to share this content if you liked it. Many thanks for your time. Come back soon.
Book Today